70-741 | 100% Correct 70-741 Braindumps 2019

Master the 70-741 exam content and be ready for exam day success quickly with this 70-741 dumps. We guarantee it!We make it a reality and give you real 70-741 exam in our Microsoft 70-741 braindumps. Latest 100% VALID 70-741 dumps at below page. You can use our Microsoft 70-741 braindumps and pass your exam.

Check 70-741 free dumps before getting the full version:

NEW QUESTION 1
You have Hyper-V host named Server1.
Server1 has a network adapter that has virtual machine queue (VMQ) enabled. The network adapter connects at 10 Gbps and has an IPv4 address.
Server1 hosts a virtual machine named VM1. VM1 has a single network adapter and four processors. You need to distribute the network processing load across the VM1 processors.
What should you do?

  • A. From Device Manager on Server1, configure TCP Checksum Offload (IPv4).
  • B. From Device Manager on VM1, configure TCP Checksum Offload (IPv4).
  • C. From Device Manager on VM1, configure Receive Side Scaling.
  • D. From Windows PowerShell on Server1, run the Enable-NetAdapterRSS cmdlet.

Answer: C

NEW QUESTION 2
Note: This question is part of a series of questions that use the same scenario. For your convenience, the scenario is repeated in each question. Each question presents a different goal and answer choices, but the text of the scenario is exactly the same in each question in this series.
Your network contains an Active Directory domain named contoso.com. The functional level of the domain is Windows Server 2012.
The network uses an address space of 192.168.0.0/16 and contains multiple subnets. The network is not connected to the Internet.
The domain contains three servers configured as shown in the following table.
70-741 dumps exhibit
Client computers obtain TCP/IP settings from Server3.
You add a second network adapter to Server2. You connect the new network adapter to the Internet. You install the Routing role service on Server2.
Server1 has four DNS zones configured as shown in the following table.
70-741 dumps exhibit
You need to ensure that when a computer is removed from the network, the associated records are deleted automatically after 15 days.
Which two actions should you perform? Each correct answer presents part of the solution.

  • A. Create a scheduled task that runs the Remove-Computer cmdlet.
  • B. Modify the Zone Aging/Scavenging Properties of the zone.
  • C. Modify the Time to live (TTL) value of the start of authority (SOA) record.
  • D. Set the Scavenging period of Server1.
  • E. Modify the Expires after value of the start of authority (SOA) record.

Answer: BD

Explanation: https://technet.microsoft.com/en-us/library/cc771362(v=ws.10).aspx

NEW QUESTION 3
You have a server named Server1 that runs Windows Server 2016. You need to configure Server1 as a multitenant RAS Gateway. What should you install on Server1?

  • A. the Network Controller server role
  • B. the Data Center Bridging feature
  • C. the Remote Access server role
  • D. the Network Policy and Access Services server role

Answer: C

NEW QUESTION 4
Your network contains an Active Directory domain named contoso.com. The domain contains a server named Server1 that runs Windows Server 2016.
You install IP Address Management (IPAM) on Server1.
You need to manually start discovery of the servers that IPAM can manage in contoso.com.
Which three cmdlets should you run in sequence? To answer, move the appropriate cmdlets from the list of cmdlets to the answer area and arrange them in the correct order.
70-741 dumps exhibit

    Answer:

    Explanation: https://technet.microsoft.com/itpro/powershell/windows/ipam/add-ipamdiscoverydomain https://technet.microsoft.com/itpro/powershell/windows/ipam/add-ipamserverinventory https://technet.microsoft.com/itpro/powershell/windows/ipam/invoke-ipamserverprovisioning

    NEW QUESTION 5
    Note: This question is part of a series of questions that use the same or similar answer choices. An answer choice may be correct for more than one question in the series. Each question is independent of the other questions in this series. Information and details provided in a question apply only to that question.
    Your network contains Windows and non-Windows devices.
    You have a DHCP server named Server1 that has an IPv4 scope named Scope1.
    You need to prevent a client computer that uses the same name as an existing registration from updating the registration.
    What should you do?

    • A. From the properties of Scope1, modify the Conflict detection attempts setting.
    • B. From the properties of Scope1, configure Name Protection.
    • C. From the properties of IPv4, configure the bindings.
    • D. From IPv4, create a new filter.
    • E. From the properties of Scope1, create an exclusion range.
    • F. From IPv4 run the DHCP Policy Configuration Wizard.
    • G. From Control Panel, modify the properties of Ethernet.
    • H. From Scope1, create a reservation.

    Answer: B

    NEW QUESTION 6
    Note: This question is part of a series of questions that present the same scenario. Each question in the series contains a unique solution that might meet the stated goals. Some question sets might have more than one correct solution, while others might not have a correct solution.
    After you answer a question in this sections, you will NOT be able to return to it. As a result, these questions will not appear in the review screen.
    You have a Hyper-V host named Server1 that hosts a virtual machine named VM1. Server1 and VM1 run Windows Server 2016.
    The settings for VM1 are configured as shown in the exhibit below.
    70-741 dumps exhibit
    You need to ensure that you can use the Copy-VMFile cmdlet on Server1 to copy files from VM1.
    Solution: You start the Hyper-V Guest Service Interface service on VM1. Does this meet the goal?

    • A. YES
    • B. NO

    Answer: B

    NEW QUESTION 7
    Your network contains multiple wireless access points (WAPs) that use WPA2-Personal authentication. The network contains an enterprise root certification authority (CA).
    The security administrator at your company plans to implement WPA2-Enterprise authentication on the WAPs.
    To support the authentication change, you deploy a server that has Network Policy Server (NPS) installed. You need to configure NPS to authenticate the wireless clients.
    What should you do on the NPS server?

    • A. Add RADIUS clients and configure network policies.
    • B. Create a remote RADIUS server group and configure connection request policies.
    • C. Create a remote RADIUS server group and install a server certificate.
    • D. Add RADIUS clients and configure connection request policies.

    Answer: A

    Explanation: https://ittrainingday.com/2013/12/25/how-to-configure-a-windows-radius-server-for-802-1x-wireless-or-wired-c

    NEW QUESTION 8
    You have servers named Server1 and DHCP1. Both servers run Windows Server 2016. DHCP1 contains an IPv4 scope named Scope1.
    You have 1,000 client computers.
    You need to configure Server1 to lease IP addresses for Scope1. The solution must ensure that Server1 is used to respond to up to 30 percent of the DHCP client requests only.
    You install the DHCP Server server role on Server1. What should you do next?

    • A. From the DHCP console, run the Configure Failover wizard.
    • B. From Server Manager, install the Network Load Balancing feature.
    • C. From Server Manager, install the Failover Clustering feature.
    • D. From the DHCP console, create a superscope.

    Answer: A

    Explanation: https://technet.microsoft.com/en-us/library/hh831385(v=ws.11).aspx

    NEW QUESTION 9
    Note: This question is part of a series of questions that use the same or similar answer choices. An answer choice may be correct for more than one question in the series. Each question is independent of the other questions in this series. Information and details provided in a question apply only to that question.
    Your network contains an Active Directory domain named contoso.com. The domain contains a server named Server2 that runs Windows Server 2016.
    The DHCP Server server role is installed on Server2. The DNS server role is installed on a server named Server3.
    The network contains 500 non-Windows devices that are registered in the DNS zone of contoso.com. You configure Server2 to lease IP addresses to the non-Windows devices.
    You need to prevent Server2 from overwriting the host (A) records for the non-Windows devices. What should you run?

    • A. dns.exe
    • B. dnscmd.exe
    • C. netsh.exe
    • D. Set-DhcpServerDatabase
    • E. Set-DhcpServerv4DnsSetting
    • F. Set-DhcpServerv6DnsSetting
    • G. Set-DNSServerSetting

    Answer: C

    Explanation: References:
    https://docs.microsoft.com/en-us/windows-server/administration/windows-commands/dnscmd

    NEW QUESTION 10
    Note: This question is part of a series of questions that present the same scenario. Each question in the series contains a unique solution. Determine whether the solution meets the stated goals.
    Refer to exhibit:
    70-741 dumps exhibit
    Server1 has two virtual machines named VM1 and VM that run Windows Server 2016. VM1 connects to Private VM2 has two network adapters.
    You need to ensure that VM1 connects to the corporate network by using NAT.
    Solution: You connect VM2 to private1 and External1. You run the New-NetNatIpAddress and the New-NetNat cmdlets on VM2. You configure VM1 to use VM2 as the default gateway.
    Does this meet the goal?

    • A. Yes
    • B. No

    Answer: B

    NEW QUESTION 11
    Your company has a branch office that has three floors. The office currently uses a different subnet on each floor. The subnets are configured as shown in the following table.
    70-741 dumps exhibit
    You have been asked to use reconfigure the network to use one subnet that encompasses all three floors. The new subnet will come from the 192.168.0.0/16 address space.
    You need to identify which IP address and which subnet mask to use for the default gateway. The solution must meet the following requirements:
    • Use the first available subnet
    • Use a single subnet for all three floors.
    • Use the first available IP address on the segment for the default gateway.
    • Minimize the number of unused IP addresses.
    Which IP address and which subnet mask should you identify? To answer, select the appropriate options in the answer area.
    70-741 dumps exhibit

      Answer:

      Explanation: 70-741 dumps exhibit

      NEW QUESTION 12
      Note: This question is part of a series of questions that present the same scenario. Each question in the series contains a unique solution. Determine whether the solution meets the stated goals.
      Refer to exhibit:
      70-741 dumps exhibit
      Server1 has two virtual machines named VM1 and VM that run Windows Server 2016. VM1 connects to Private VM2 has two network adapters.
      You need to ensure that VM1 connects to the corporate network by using NAT.
      Solution: You connect VM1 to Internal1. You run the New-NetNatIpAddress and the New-NetNat cmdlets on Server1. You configure VM1 to use VM2 as the default gateway.
      Does this meet the goal?

      • A. Yes
      • B. No

      Answer: A

      NEW QUESTION 13
      You are implementing a new network. The network contains a DHCP server named DHCP1 that runs Windows Server 2016. DHCP1 contains a scope named Scope1 for the 192.168.0/24 subnet.
      Your company has the following policy for allocating IP addresses:
      70-741 dumps exhibit All server addresses must be excluded from DHCP scopes.
      70-741 dumps exhibit All client computer must receive IP addresses from Scope1.
      70-741 dumps exhibit All Windows servers must have IP addresses in the range of 192.168.0.200 to 192.168.0.240
      70-741 dumps exhibit All other network devices must have IP addresses in the range of 192.168.0.180 to 192.168.0.199. You deploy a print device named Print1.
      You need to ensure that Print1 adheres to the policy for allocating IP addresses. Which command should you use?

      • A. Add-DhcpServerv4Lease
      • B. Add-DhcpServerv4ExclusionRange
      • C. Add-DhcpServerv4Filter
      • D. Add-DhcpServerv4Reservation

      Answer: D

      NEW QUESTION 14
      You have a server named Server1 that runs Windows Server 2016 and is configured as a domain controller. You install the DNS Server server role on Server1.
      You plan to store a DNS zone in a custom Active Directory partition. You need to create a new Active Directory partition for the zone. What should you use?

      • A. Set-DnsServer
      • B. Active Directory Sites and Services
      • C. Dns.exe
      • D. Dnscmd.exe

      Answer: D

      Explanation: https://technet.microsoft.com/en-us/library/ee649181(v=ws.10).aspx

      NEW QUESTION 15
      You have a virtual machine named Server1 that runs Windows Server 2016.
      You plan to use Server1 as part of a Software Defined Networking (SDN) solution.
      You need to implement the Border Gateway Protocol (BGP) on Server1. What should you install?

      • A. the peer Name Resolution Protocol (PNRP)feature
      • B. the Routing role service
      • C. the Network Device Enrollment Service role service
      • D. the Network Policy and access Services server role

      Answer: B

      Explanation: References:
      https://docs.microsoft.com/en-us/windows-server/remote/remote-access/bgp/border-gateway-protocol-bgp

      NEW QUESTION 16
      Note: This question is part of a series of questions that present the same scenario. Each question in the series contains a unique solution. Determine whether the solution meets the stated goals.
      Refer to exhibit:
      70-741 dumps exhibit
      Server1 has two virtual machines named VM1 and VM that run Windows Server 2016. VM1 connects to Private VM2 has two network adapters.
      You need to ensure that VM1 connects to the corporate network by using NAT.
      Solution: You connect VM2 to private1 and External1. You install the Remote Access Serverrole on VM2, and you configure NAT in the Routing and Remote Access console. You configure VM1 to use VM2 as the default gateway.
      Does this meet the goal?

      • A. Yes
      • B. No

      Answer: A

      NEW QUESTION 17
      You have a Hyper-V server named Server1 that runs Windows Server 2016. Server1 has an IP address of 192.168.1.78. Server1 has a container named Container1 that hosts a web application on port 84. Container1 has an IP address of 172.16.5.6. Container1 has a port mapping from port 80 on Server1 to port 84 on Container1. You have a server named Server2 that has an IP address of 192.168.1.79, You need to connect to the web application from Server2. To which IP address and port should you connect?

      • A. 172.16.5.6:80
      • B. 192.168.1.78:80
      • C. 172.16.5.6:84
      • D. 192.168.1.78:84

      Answer: C

      NEW QUESTION 18
      Note: This question is part of a series of questions that present the same scenario. Each question in the series contains a unique solution that might meet the stated goals. Some question sets might have more than one correct solution, while others might not have a correct solution.
      After you answer a question in this sections, you will NOT be able to return to it. As a result, these questions will not appear in the review screen.
      You have a Hyper-V host named Server1 that hosts a virtual machine named VM1. Server1 and VM1 run Windows Server 2016.
      The settings for VM1 are configured as shown in the exhibit below.
      70-741 dumps exhibit
      You need to ensure that you can use the Copy-VMFile cmdlet on Server1 to copy files from VM1.
      Solution: You need to enable the Data Exchange integration service for VM1. Does this meet the goal?

      • A. YES
      • B. NO

      Answer: B

      NEW QUESTION 19
      You have multiple servers that run Windows Server 2016 and are configured as VPN servers. You deploy a server named NPS1 that has Network Policy Server (NPS) installed.
      You need to configure NPS1 to accept authentication requests from the VPN servers. What should you configure on NPS1?

      • A. From RADIUS Clients and Servers, add a remote RADIUS server group.
      • B. From Policies, add a connection request policy.
      • C. From Policies, add a network policy.
      • D. From RADIUS Clients and Servers, add RADIUS clients.

      Answer: D

      NEW QUESTION 20
      You have an Active Directory domain named Contoso.com. The domain contains Hyper-V hosts named Server1 and Server2 that run Windows Server 2016. The Hyper-V hosts are configured to use NVGRE for network virtualization.
      You have six virtual machines that are connected to an external switch. The virtual machines are configured as shown.
      70-741 dumps exhibit
      To which virtual machine or virtual machines can VM1 and VM3 connect? To answer, select the appropriate options in the answer area.
      70-741 dumps exhibit

        Answer:

        Explanation: The GRE keys must match.
        To separate the traffic between the two virtualized networks, the GRE headers on the tunneled packets include a GRE Key that provides a unique Virtual Subnet ID for each virtualized network.
        References:
        https://blogs.technet.microsoft.com/keithmayer/2012/10/08/step-by-step-hyper-v-network-virtualization-31-days

        P.S. 2passeasy now are offering 100% pass ensure 70-741 dumps! All 70-741 exam questions have been updated with correct answers: https://www.2passeasy.com/dumps/70-741/ (235 New Questions)